XP DEUS II issues

SuMMARY: XP Deus II gives too many bad (grunt, inconsistent) signals in one area
Possible Causes :
1) electric fencing/Train lines nearby
2) frequency scan gone wrong (several times)
3) bad settings (audio response 5).
4) dry soil (which couldn’t be it, cos it happened on very sticky mud too)

Against electric fencing: THe Deus I would work perfectly in that same field, but would give intermittent beeps when too close to the electric fencing. Deus II gave no sign of interference thoughso it operated quietly on the whole area.
Against bad settings: I tried a myriad of presets and other personalised settings.
Frequency scan did turn the bad detector into a good detector in another area. Took it to the first spot and it worked fine all of a sudden.

Conclusion : until otherwise proven, I guess the issue has been resolved.
1) :p I’m not allowed on that problematic area anymore because the landowner was very unpleasant towards me, eventhough he did give me permission before.
2) I’m now successfully detecting another area which is directly under high voltage and the issue is gone ! It does give some intermittent beeps around one spot but the rest is pretty quiet.
No more constant bad low signals and I get plenty of good signals, small targets, deep targets, and almost no iron, wheras before I’d dig a lot of iron when the signal was good (which rarely happened because all signals were low, or fleeting).

OLD POST———————————–:
I have to investigate this issue further but for now, here is what is happening:

There’s this field that I call My Best Field because in one year I found so many cool things there.
Last year there was stubble, and ground was superhard. Went over it a few times and didn’t find much, because of stubble and hard soil (I wasn’t happy to dig a lot).
Few months ago I went with Deus II over the freshly ploughed field nearby and it gave nothing but very low and bad signals. A few rare good signals ended up being deep rusty iron or some lead. The lead was the only good stuff I found and the number of good signals was just depressing, I think 12 in two hours. But it happened before like that so ok..

Today, however, my best field was free and the stubble had been turned around so i was superhappy. I went on it and in 10mins I realized I was again only getting low signals.
Changed settings, tone, reactivity, even tried mono.
Went around for one hour, only getting bad sounds, and a few good signals that turned out to be lead or iron (3x).
Few hours later I go on same type of soil in another place, did also feel like bad signals only, then I did a freq scan and it was fine ! Good signals and good amount of signals too. So there was something that changed with the frequency scan that made it work again like I would expect.

Getting only bad signals is SO depressing ! I know there were periods where there was just almost nothing to dig and it was just a matter of living through. This is different. THis is a detector working here and then not working there. I’m not sure if i tried it anywhere else.. i remember using the old Deus again in other places and it was fine. Also used the Deus II somewhere else this week and it was fine. So I’m considering it place-related an also .. maybe i can not do the freq scan and it would work in this bad spot ?

13 yrs anniversary of detecting !

soem stuff the Deus won’t find but pinpointer picks it all up.

Apparently I got my first detector exactly 13 yrs ago. It was a used Garrett 250 and I found absolutely nothing with it. I wrote down what I found in the garden while all was beeping: a rat’s tunnel, some pieces of jar, the wires going to the pond..
Let’s hope I can get back at it after a small year of break. I kinda had it with the bad results and the new Deus II wasn’t really helping as I had no clue what the signals meant anymore.
Deus I should still do its job; it’s just that there are a lot of bad targets and not a lot of good ones lately. Fields are now supposed to have something growing when Winter starts so a lot of fields aren’t going to be available.